Mastering DA converter
Mercury is the first Mastering DA converter in 120V rail technology.
Mercury is a stereo digital to analog converter that fulfills the highest demands both technologically and tonally.
A total of seven digital inputs, two AES/EBU, two SPDIF, two TOSLINK as well as USB can be connected to Mercury. AES input 2 also supports Dual-Wire (DW) mode.
Each digital sources has its dedicated and illuminated switch for instant selection and fast comparison.
- DAC with DLP120
- Velvet Sound® DA Converter
- AES & DW
- DSD via USB
- PCM & DSD
- Volume Control
- 0dBfs Reference Level
We have 30 years of experience in analog technology and consider ‘cookbook’ designs rather boring, inefficient and in need of improvement.
The output of the DAC-IC (AK4490) is an analog signal that must be filtered with a low-pass filter. This analog circuit is typically operated with the same voltage as the DAC-IC - for example 5V. Imagine that the first stage that finds the analog signal has a dynamic range and signal-to-noise ratio limited by this voltage. What a bottleneck.
The Mercury uses our 120V technology instead of the standard technology. And this twice in the newly developed DLP120 module. DLP stands for "Dual Low Pass". These are two separate analog filters in 120V technology. Depending on the type of digital signal, the analog signal passes through the PCM or DSD filter and can freely unfold into a huge dynamic range. This is audibly better.
It offers a bit depth of 32 bits and a maximum sampling rate of 768kHz for PCM digital signals and DSD4 or DSD256 for direct-stream digital signals.
An AES signal transports two encoded PCM audio channels at a maximum sampling rate of 192 kHz.
The standard is defined under IEC 60958 Type I.
A special feature is the Dual-Wire mode (DW), where two AES jacks are operated together to double the maximum sampling rate. The second AES input therefore has two XLR jacks. Dual-Wire allows Mercury to be connected to any digital AES/EBU source.
Balanced, 3-core, 110 Ohm "twisted pair" cables with XLR plugs are used for connection.
The jacks are labeled "Coaxial" and carry two encoded PCM audio channels with sampling rates up to 192kHz.
This standard is defined under IEC 60958 Type II.
Unbalanced, 2-wire 75-Ohm coaxial cables with RCA connectors are used for connection.
These jacks are labeled "Optical" on Mercury.
Just like the coaxial S/P-DIF inputs, these inputs support sampling rates up to 192kHz for encoded PCM audio.
Our tip: You should attach importance to the quality of the optical fiber. With inexpensive plastic optical fibers, transmissions with fourfold sampling rates (176.4kHz/192kHz) can be subject to errors. In this case a real fibre optic cable should be chosen.
Sample rates up to 768kHz are supported for PCM audio. For DSD audio up to DSD4 (quad-rate DSD or DSD256).
No special driver is required for an Apple Mac, as Apple natively supports USB class 2 up to a sampling rate of 768kHz.
To use Mercury to its full extent on a Windows PC, the SPL Mercury driver should be installed. With this driver, higher sampling rates than 44.1kHz and 48kHz can be output on a Windows PC.
Specific software players such as Audirvana Plus (Mac), Channel D Pure Music (Mac), J River Media Center (Mac/PC), Signalyst (PC), Foobar2000 (PC), JPlay (PC) support DSD playback.
The USB Audio 2.0 specification defines different formats for handling PCM audio signals, but it does not define the handling of the DSD format. In 2012, representatives of many companies and institutions have developed a standard known as "DSD over PCM" or "DoP". This will represent and detect DSD audio in the PCM frames of the USB specification.
SACD or BluRay players usually do not output the DSD stream for copy protection reasons. This means that such a player can only be connected to one analog input, e.g. on the SPL DMC Mastering Console.
Direct-Stream Digital (DSD) is a trademark of Sony and Philips. Both developed DSD for SACD (Super Audio CD), which was to become the designated successor to the CD (which was also developed by the two companies).
Since PCM and DSD are digital formats, there are other ways of playback. The highest resolutions for music are now available from download portals such as HD Tracks, Qobuz, HIGHRESAUDIO, primephonic, HDMusicStore, Bleep, Cybele, Gimell, HD-Klassik, 7 Digital etc.
DSD is fundamentally different from conventional PCM. While in a PCM stream the amplitude of an analog signal is sampled regularly at equal intervals and each sample thus obtained is quantized to the closest value within the digital stages, a DSD stream stores a sequence of 1-bit values before a "decimation" process converts the signal into a PCM signal.
The volume control for the variable output of the Mercury is completely analog. In most other designs the volume control is done digitally as part of the converter chip functionality. A disadvantage of digital volume control is that the original bit resolution is only available at 0dB (maximum value).
As volume control we use the ALPS RK27 "Big Blue" potentiometer which provides a nice, sensitive feeling and excellent channel synchronisation. So not only the auditory, but also the haptic experience is on the highest level when adjusting the volume.
Mercury supports all currently used reference levels starting with 0dBfs = 14dBu. Followed by 15, 16, 17, 18, 20, 22 and finally 24dBu.