PROFESSIONAL FIDELITY

Crossover

Finally an analog crossover again

It is difficult to optimally integrate bass loudspeakers or subwoofers.
At present, there are almost only digital crossovers for this purpose.
But who wants to convert back to digital in an analog high-end playback chain?
Our Crossover sets the crossovers anew.

Crossing over

The crossover is divided into two sections: The Low section for the bass loudspeaker or subwoofer (mono or stereo) and the Mid-Hi section for the top/main speakers.

The crossover frequencies for Low and Mid-Hi can be set individually from 50 Hz to 120 Hz in 6 positions.

The Low filter has a slope of 24 dB per octave. The slope of the MID-HI filter can be switched from 12 dB to 24 dB.

In Phase

Audio signals should come from the top speakers and bass loudspeakers or subwoofers in phase.
The crossover offers variable phase control for this purpose.

Use the toggle switch to activate the phase control (phase 0° or phase -180°) and use the control to establish simultaneousness.

If the phase control is not required, it can be switched off and thus disappears completely from the signal path.

One or two?

If you want to connect two bass loudspeakers or subwoofers (one for L and one for R), this switch should be set to stereo.

If you only use one bass loudspeaker or subwoofer, switch to mono. The crossover creates a mono signal of the Low frequencies and outputs it to both Low outputs (L + R).

“In practice, it is easy to integrate a subwoofer into an existing loudspeaker concept with the Crossover. Flexible, easy to adjust and with a sound that is undetectable when configured correctly: Respect, SPL!”

On or off?

If you prefer to run the top/main speakers full-range, you can switch off the MID-Hi filter.

Get rid off it

With the Low Cut filter all frequencies below 20 Hz can be filtered out.

This way, the power amplifier does not have to amplify inaudible low frequencies and the loudspeaker is relieved.

As long as you're having fun

The playback volume of the bass loudspeaker or subwoofer can be varied from -10 dB to +10 dB.

In addition to the purely corrective adjustment of the speaker system, you can add more bass into recordings that lack low end.

“Happiness is when the bass kicks in.”

Good ol' times

Two mechanical VU meters visualize the input levels for the left and right audio channel.

With the VU switch you can optimize the display for different signal levels.

Source of joy

The Crossover offers both balanced inputs with XLR sockets and standard inputs with gold-plated RCA sockets.

Low & Mid-Hi

On the output side, the power amplifiers or active loudspeakers as well as bass loudspeakers or subwoofers are connected to the Low & Mid-Hi output sockets by means of balanced XLRs.

This means that even long cable runs to e.g. mono power amps placed next to the speaker are possible without the risk of interference.

Everything under control – AMP CTL

The standby mode for up to four devices with 12V trigger input can be switched on and off via AMP CTL, together with the Crossover (AMP CTL Out). This is especially useful for connecting power amplifiers. But also the standby mode of the Crossover itself can be switched on and off by a preamplifier, such as the Director Mk2 or the Phonitor x, via AMP CTL (AMP CTL In).

Sounds good

With all devices of the Professional Fidelity series we develop not only according to plan, but also by ear. Many important components are installed on the circuit boards using Through-hole technology. This way we can ensure that we can use the best sounding components.

The VOLTAiR Technology

The 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps. In our Professional Fidelity series, we refer to this unsurpassed technology as VOLTAiR technology.

The highest possible audio quality requires the highest possible audio operating voltage.

The 120V technology works with +/-60 V. To be able to handle such a high voltage, we have developed special proprietary operational amplifiers that can operate with a DC voltage of +/-60 V: the SPL 120V SUPRA operational amplifiers. This high voltage would destroy conventional components and operational amplifiers.

The 120V technology achieves exceptional technical specifications and sonic benefits. Technically, in terms of dynamic range, signal-to-noise ratio and headroom. Sonically, in terms of richness of detail and an absolutely relaxed listening experience. 

By the way, the “120V” in the name of the technology has nothing to do with the local mains voltage from the mains power socket. This is about the operating voltage inside the device with which the audio signals are processed.

The mains voltage from the mains power socket is transformed to the required secondary voltage in the device’s internal linear power supply with toroidal transformer. Rectifiers convert this AC voltage into DC voltage required in the audio device.

VOLTAiR is a composition of the terms Volt and Air. Volt is the unit for electrical voltage and Air stands for the unlimited space the music can breathe in.

VOLTAiR symbolizes the perceived limitless dynamics resulting from high audio voltage.

What exactly is that?

And what does it do?

Good questions need good answers.

And that’s what the 120V technology (VOLTAiR) video gives you.

Play Video

Comparison

Most audio devices work with an internal operating voltage of +/-15 volts and can thus process a maximum input level of +21.5 dBu. If a DAC, for example, has an output level of +22 dBu at 0 dBFS, level peaks of the music material would already cause overloads in the input stage of the device. All components in the audio device often operate at their limits. The result is an unsteady sound that causes stress and faster ear fatigue.

SPL devices with VOLTAiR technology can handle input levels of +32.5 dBu thanks to the higher internal operating voltage of +/- 60 volts – thus offering 12 dB more headroom. All components consequently operate continuously in the optimum operating range. The result is a very pleasant, natural and relaxed sound experience. So you can enjoy your music in every detail.

These diagrams clearly show the superiority of the VOLTAiR technology in comparison to other circuits with lower, common operating voltages.

Home is where the heart is

That’s why we manufacture all SPL devices in our own production facility in Niederkrüchten on the Lower Rhine, Germany.

VOLTAiR is that good

In the lab, we pitted Phonitor xe against the best audio measurement system and found that Audio Precision could not measure VOLTAiR technology.

Play Video

Slimmer is smarter

Play Video
This video guides you step by step through the Crossover.

Videos

Play Video
SPL Analog Active Crossover Review
Play Video
Interview about VOLTAiR Technology and SPL at High End 2022
Play Video
Hi-Fi Setup with SPL Crossover

Reviews

HiFi-Stars

Manuals

Replacing fuses and voltage selection

The replacement of fuses and the switching of mains voltages must only be performed by qualified technicians. Fuses must only be replaced with fuses of the same type and specifications.

Play Video
Replacement of defective fuses for 115V
Play Video
Replacement of defective fuses for 230V
Play Video
Changing the mains voltage from 115V to 230V
Play Video
Changing the mains voltage from 230V to 115V

Specifications

Analog Inputs & Output: XLR (balanced) and RCA

Maximum input & output gain
32.5 dB
Input impedance (RCA)
20
Input impedance (XLR)
20
Output impedance
75 Ω
Common mode rejection (XLR)
-82 dBu
Frequency range (-3 dB)
10 Hz – 100 kHz
Crosstalk (1 kHz)
-70 dBu
THD (0 dBu, 1 kHz, MID-Hi filter on)
0.0008 %
THD (0 dBu, 30 Hz, LOW filter on)
0.0014 %
Noise (A-weighted, MID-HI output)
-106 dBu
Noise (A-weighted, LOW output)
-104.9 dBu
Dynamic range (MID-HI output)
138 dB
Dynamic range (LOW output)
136.9 dB

Internal Linear Power Supply with Shielded Toroidal Transformer

Operating voltage for analog audio
+/- 60 V
Operating voltage for relays and LEDs
+ 12 V

Mains Power Supply

Mains voltage (selectable, see fuse chamber)
230 V AC / 50; 115 V AC / 60 Hz
Fuse for 230 V
T 0.5 A
Fuse for 115 V
T 1 A
Power consumption
max. 50 VA
Stand-by power consumption
< 0.3 W

Dimensions & Weight

W x H x D (width x height incl. feet x depth)
278 x 100 x 300 mm
11 x 4 x 11.81 inch
Unit weight
5 kg
11,02 lbs
Shipping weight (incl. packaging)
5.95 kg
13.12 lbs

Reference: 0 dBu = 0.775V. All specifications are subject to change without notice.

Other Professional Fidelity Series Products

Phonitor-xe_front_silver_2560px
Phonitor xe
Headphone Amplifier
Phonitor-x_front_silver_1280
Phonitor x
Headphone Amplifier and Preamplifier
Phonitor_se_front_silver
Phonitor se
Headphone Amplifier
Director-MK2_front_silver_2560
Director Mk2
Preamplifier with DA converter
Diamond_front_silver
Diamond
D/A-Converter
Elector_front_silver
Elector
Analog Preamplifier
Phonitor-x_front_silver_1280
Phonitor x
Headphone Amplifier and Preamplifier
Phonos_front_silver
Phonos
RIAA Phono Preamplifier
Performer-s900_Front_Silver
Performer s900
Stereo Power Amplifier
Performer_s1200_front_silver_silver
Performer s1200
Stereo Power Amplifier
Performer-m1000_front_silver_silver
Performer m1000
Mono Power Amplifier
Performer-s800_front_silver
Performer s800
Stereo Power Amplifier

Professional Fidelity Brochure

Flag
Flag
ProAudio
HiFi
ProAudio
HiFi

Calculation of VAT (value added tax)

All prices are displayed by default including the VAT of your country.

If your country cannot be determined via geolocation and you are not logged in as a user with the billing address of your country, the prices are displayed including the VAT of Germany (19%).

What does it actually mean …

In Stock!

The product is in stock in our warehouse in Niederkrüchten, Germany, and will be shipped the same or next working day.

We process the orders after receipt of the order and update the stock in the online shop regularly. If the product is no longer available at short notice due to high order volume, you naturally have the right to withdraw from the purchase (see Right of Withdrawal).

In any case, you will receive an e-mail with details of the delivery and the estimated delivery time.

Available soon!

The product is not in stock in our warehouse in Niederkrüchten, Germany. Usually it will be available again within 5 working days.

In any case, you will receive an e-mail with the details of the delivery and the estimated delivery time.

Of course you have the right to withdraw from your purchase (see Right of Withdrawal).

Currently unavailable.

This product is currently sold out and unavailable.

Was bedeutet eigentlich …

Auf Lager!

Das Produkt ist in unserem Lager Niederkrüchten vorrätig und wird noch am selben oder nächsten Werktag versendet.

Wir arbeiten die Bestellungen nach Bestelleingang ab und aktualisieren den Bestand im Online-Shop regelmäßig. Falls das Produkt wegen hohem Bestellaufkommens kurzfristig nicht mehr verfügbar ist, hast du selbstverständlich das Recht, vom Kauf zurückzutreten (siehe Widerrufbelehrung).

In jeden Fall erhältst du eine E-Mail mit den Einzelheiten der Lieferung und der voraussichtlichen Lieferzeit.

Bald verfügbar!

Das Produkt ist in unserem Lager Niederkrüchten nicht vorrätig. Gewöhnlich ist es innerhalb von 5 Werktagen wieder verfügbar.

Auf jeden Fall erhältst du eine E-Mail mit den Einzelheiten der Lieferung und der voraussichtlichen Lieferzeit.

Selbstverständlich hast du das Recht, vom Kauf zurückzutreten (siehe Widerrufbelehrung).

Zur Zeit nicht verfügbar.

Dieses Produkt ist derzeit ausverkauft und nicht verfügbar.

Events

Due to Covid19 there are no events scheduled at this time.

Events

Aufgrund von Covid19 sind derzeit keine Events geplant.

Anmelden